Senior Embedded Systems Engineer (Electrical / Firmware)
Colorado Springs, CO
Full Time
R and D
Experienced
Senior Embedded Systems Engineer (Electrical / Firmware)
Skyline Products
Location: Colorado Springs, CO
Job Type: Full-Time
Reports To: Director of Engineering
Salary Range: $110,000. To $140,000. Annually
Travel: Up to 10% for field visits to customer sites and contract manufacturers
Industry: Transportation / Intelligent Transportation Systems (ITS)
This role sits squarely at the intersection of hardware and software. You’ll develop firmware for bare-metal microcontrollers and embedded Linux controllers, contribute to circuit and PCB design, and serve as a go-to engineer for problems that don’t stay neatly on one side of the hardware/software line, from a dead pixel on the bench to an intermittent communication fault on a sign mounted to an overpass. The ideal candidate is a methodical troubleshooter who is equally comfortable with a scope probe, a schematic, and a debugger, and who doesn’t consider a problem closed until the root cause is proven.
Skyline Products
Location: Colorado Springs, CO
Job Type: Full-Time
Reports To: Director of Engineering
Salary Range: $110,000. To $140,000. Annually
Travel: Up to 10% for field visits to customer sites and contract manufacturers
Industry: Transportation / Intelligent Transportation Systems (ITS)
About Skyline Products
Skyline Products designs and manufactures LED dynamic message signs and electronic price signs from our facility in Colorado Springs. For more than 55 years, our signs have been installed on highways, toll roads, and fueling stations across the United States, delivering information that drivers rely on every day. We are a focused engineering and manufacturing team where your work goes directly into products in the field.About the Role
We are looking for a Senior Embedded Systems Engineer with an electrical engineering foundation to join our engineering team developing LED message signs and control systems for the transportation industry. These signs are installed over highways and play a critical role in public safety and traffic management.This role sits squarely at the intersection of hardware and software. You’ll develop firmware for bare-metal microcontrollers and embedded Linux controllers, contribute to circuit and PCB design, and serve as a go-to engineer for problems that don’t stay neatly on one side of the hardware/software line, from a dead pixel on the bench to an intermittent communication fault on a sign mounted to an overpass. The ideal candidate is a methodical troubleshooter who is equally comfortable with a scope probe, a schematic, and a debugger, and who doesn’t consider a problem closed until the root cause is proven.
Key Responsibilities
- Lead root-cause investigations of field, production, and lab failures that span firmware, circuitry, components, PCB assembly, cabling/connectors, and environmental stress (heat, vibration, moisture), and drive them to verified corrective action
- Design, develop, and maintain embedded firmware in C/C++ on bare-metal microcontrollers (e.g., PIC, STM32/ARM Cortex-M) and RTOS-based platforms
- Build and maintain embedded Linux applications and system configuration on sign controllers, including networking, security hardening, storage, and boot configuration
- Contribute to and maintain existing, long-lived codebases, ensuring stability, clarity, and documentation
- Participate in electronic hardware design: schematic review, PCB layout review, component selection, and board bring-up
- Develop and tune RGB LED color mixing: per-color current and PWM balancing, white-point and color-matching across LED bins, and brightness/color consistency over temperature and dimming levels
- Evaluate and qualify components for long-life outdoor deployment (microcontrollers, LED drivers, LEDs, connectors, power and storage devices), including replacements for obsolete or unavailable parts
- Design and build test fixtures, automated test rigs, and lab tools (Python plus instrumentation) to reproduce intermittent failures and validate fixes
- Debug hardware/software issues using oscilloscopes, logic and protocol analyzers, JTAG/SWD debuggers, and other bench instruments
- Support production, contract manufacturers, and field service with failure analysis, pre-installation sign inspections, and on-site troubleshooting when needed
- Design systems with long-term reliability, diagnostics, and field maintainability in mind
- Ensure compliance with transportation and industry standards (e.g., NTCIP, NEMA TS 4) for robustness and safety
- Write and maintain technical documentation, including design documents, test procedures, failure analysis reports, and controlled quality documents
Required Qualifications
- Bachelor’s degree in Electrical Engineering (preferred) or Computer Engineering; Master’s a plus
- 5+ years of combined embedded hardware and firmware development experience
- Demonstrated, systematic troubleshooting ability across the hardware/software boundary: able to isolate whether a fault lives in firmware, circuit design, a component, assembly, or interconnect, and back the conclusion with data
- Ability to read and interpret schematics, datasheets, and PCB layouts; solid grasp of analog and digital circuit fundamentals
- Hands-on proficiency with lab instruments: oscilloscopes, logic analyzers, DMMs, power supplies, and in-circuit debuggers
- Proficiency in C in resource-constrained embedded environments (C++ a plus)
- Experience with bare-metal microcontroller development and bring-up (e.g., ARM Cortex-M, PIC, STM32)
- Understanding of low-level hardware interfaces: I2C, SPI, UART, RS-485, Ethernet (MAC/PHY), GPIO, PWM
- Working experience with embedded Linux (user-space applications, networking, SSH/user security, filesystems)
- Python for test automation, data capture/analysis, and engineering tools
- Experience with Git in shared codebases
- Clear written communication: able to write failure analysis findings for management, customers, and suppliers
Preferred Qualifications
- Experience with transportation, outdoor industrial, or safety-critical systems
- RGB LED color mixing fundamentals (color spaces, chromaticity, LED binning, per-channel current/PWM balancing)
- Familiarity with communication protocols used in ITS, such as NTCIP, SNMP, and multi-drop RS-485
- LED display technology: constant-current LED drivers, PWM grayscale, flicker-free refresh, LED thermal and failure modes
- Experience with RTOS and embedded TCP/IP stacks (e.g., FreeRTOS/lwIP, ThreadX/NetX Duo)
- Industrial networking: managed Ethernet switches, cellular modems, PPP
- PCB design tool experience (e.g., Altium, KiCad, OrCAD)
- Knowledge of PCBA manufacturing and DFM: SMT/through-hole assembly, conformal coating, connector selection and retention, and working with contract manufacturers on failure analysis
- Environmental and reliability testing: thermal (−34 to +74 °C per NEMA TS 4, and solar loading), vibration/shock, and accelerated life testing
- Knowledge of power management, backup power (supercapacitor/battery), watchdog timers, and fail-safe system design
- Experience with robust field-update mechanisms (e.g., bootloaders, remote updates)
- Exposure to EMI/EMC considerations in embedded design
- Familiarity with ISO 9001 quality systems and corrective-action processes
- Shell scripting (Bash) and comfort with Linux/WSL development environments
- 3D CAD and 3D printing for fixtures and small mechanical parts
Physical and Field Requirements
- Ability to work outdoors in varying weather conditions during field visits
- Ability to work from bucket trucks or at heights with proper safety equipment and training
- Ability to lift up to 50 lbs
- Valid driver’s license
What We Offer
- Benefits including medical, dental, and vision insurance, 401(k) with company match, and paid time off
- Work on public safety systems on Colorado highways and across the country, with real-world impact
- A small, collaborative engineering team where your work goes directly from the bench to the field
- Hybrid schedule with room for professional growth
- A chance to help shape the future of intelligent transportation infrastructure
Skyline Products is an Equal Opportunity Employer; all decisions are made without regard to race, color, religion, creed, gender, national origin, age, disability, marital or veteran status, sexual orientation, gender identity, or any other legally protected status.
Apply for this position
Required*